What is the difference between sound absorption and soundproofing?

Sound absorption reduces reflected sound inside a room, which shortens reverberation time. Soundproofing, properly called sound insulation, limits sound passing between rooms and depends mainly on the mass and construction of walls and floors. Absorbent finishes treat the sound inside a room; they are not a substitute for insulation between rooms.[1]

Key points

  • Absorption acts on the sound within a room. When a sound wave meets a surface, part is reflected and part is absorbed and dissipated as heat.[1]
  • Insulation acts between rooms. The greater the airborne sound insulation, the lower the sound level in the receiving room.[1]
  • For single-leaf elements, doubling the mass gives an increase of 5 to 6 dB in sound insulation.[1]
  • BB93 sets separate limits for ambient noise, sound insulation and reverberation time, because they are different problems.[2]

How it works

Sound in a room reaches a surface and is partly reflected and partly absorbed. A surface with a higher absorption coefficient absorbs more and reflects less, which shortens the reverberation time.[1] The effect is on the sound inside the room that the source is in.

Sound that passes into a neighbouring room does so through the separating wall or floor and through flanking paths such as ceilings and floors. The airborne sound insulation of a building element is principally controlled by its mass, with double-leaf constructions performing better than the mass law would suggest.[1] In England, Approved Document E covers sound insulation requirements including those for schools.[3]

The numbers

For a classroom, BB93 sets these three separate figures for new build and refurbishment.[2]

  • Indoor ambient noise: 35 dB new build, 40 dB refurbishment.[2]
  • Maximum mid-frequency reverberation time (primary): 0.6 s new build, 0.8 s refurbishment.[2]
  • Airborne sound insulation between two ordinary classrooms (DnT,w): at least 45 dB new build, 40 dB refurbishment.[2]

Only the second is a matter of absorption. The third is a matter of the construction between the rooms.

In schools and SEN settings

BB93 says pupils with special educational needs are generally more sensitive to the acoustic environment, so for their rooms required reverberation times are shorter, sound insulation between adjacent spaces is higher and ambient noise levels are lower.[2] The National Deaf Children's Society lists both kinds of measure when it describes improving listening conditions: reducing echoes and reverberation with fabric, carpets and specialist acoustic boarding, and fitting double glazing and keeping doors shut to limit noise coming in.[4] A school brief for a SEN room should therefore state which problem it is solving.

Worked example

These figures are illustrative. A secondary classroom measures 1.4 s reverberation time against a refurbishment limit of 1.0 s.[2] That is an absorption problem, solved by adding absorbent area. In the same building, two classrooms measure 35 dB DnT,w against a refurbishment requirement of 40 dB.[2] That is an insulation problem. Ceiling absorbers will not close the 5 dB gap, because the sound is passing through the wall and its junctions.[1]

What people get wrong

  • Calling absorbers soundproofing. The two terms describe different mechanisms, and BB93 treats them as separate performance standards.[2]
  • Upgrading the wall and ignoring the flanking path. The design guide gives a case where raising a partition to 64 dB Rw would not lift a result of 40 dB DnT,w, because most sound travelled through a screed, the dominant flanking path.[1]
  • Expecting absorption to make a noisy neighbour quiet. Absorption reduces reverberant build-up inside the room; it does not stop sound entering from outside.[1]

How it is checked

BB93 assesses airborne sound insulation as the standardised level difference DnT, measured under BS EN ISO 16283-1 and weighted to DnT,w under BS EN ISO 717-1.[2] Reverberation time is measured separately, following the Association of Noise Consultants testing guide for completed school spaces.[2]

FAQ

Is an acoustic panel soundproofing?

No. A panel is an absorber and treats sound within the room. Sound insulation between rooms depends mainly on mass and construction.[1]

Which do I need for a noisy classroom?

If speech sounds echoey and unclear inside the room, the cause is reverberation and the remedy is absorption. If noise comes from next door, the remedy is insulation, and a survey can tell the two apart.[1][2]

Does BB93 cover both?

Yes. It sets limits for reverberation time and for airborne and impact sound insulation, along with ambient noise.[2]

WorkSpace Acoustics surveys and installs acoustic treatment; contact the team to find out which problem a room has.

Sources

  1. Acoustics of Schools: a design guide. Institute of Acoustics and Association of Noise Consultants, November 2015. Accessed November 2026.
  2. Acoustic design of schools: performance standards (Building Bulletin 93). Department for Education, February 2015. Accessed November 2026.
  3. Resistance to sound: Approved Document E. Ministry of Housing, Communities and Local Government (GOV.UK), published 4 March 2015. Accessed November 2026.
  4. Creating good listening conditions. National Deaf Children's Society, last reviewed May 2025. Accessed November 2026.
Expert acoustic consultancy and installation for schools, businesses and restaurants across the UK. Specialists in SEN environments.
A specialist division of: Presentation Spaces Group

COMPANY

About
Why Acoustics
Contact Us
Privacy Policy
Glossary
Acoustics statistics

SECTORS

Schools
Businesses
Restaurants

SERVICES

Acoustic Surveys
Acoustic Design
Installation
© 2026 WorkSpace Acoustics Ltd. All rights reserved.
Product images courtesy of Presentation Spaces Group (used with permission)