Why do high-ceilinged rooms echo, and how much absorption do they need?
High-ceiling room acoustics describe how a tall room's larger volume lengthens reverberation time. By the Sabine relation, reverberation time equals 0.161 times the volume in cubic metres divided by the total absorption, so for the same absorption, doubling the volume doubles the reverberation time.[1]
Key points
- Reverberation time is proportional to room volume, so a taller room needs more absorption to reach the same target.[1]
- The Institute of Acoustics says large amounts of fixed acoustic absorption are often required in classrooms and other speech rooms, particularly where ceilings are high.[1]
- Adding absorption and reducing the ceiling height will generally reduce reverberation time and improve speech intelligibility.[1]
- BB93 sets different limits for high-volume school spaces: for new build, 1.5 s for a foyer or entrance hall and 1.5 to 2.0 s for a sports hall.[2]
How it works
The Sabine relation is T = 0.161 V ÷ A, where V is the volume in cubic metres and A the total absorption in square metres of absorption.[1] With a larger V and the same A, T grows. The design guide cautions that the relation assumes an even sound field, and that in rooms with one dimension six times or more the others, or with uneven absorption, reverberation time may vary across the space and additional descriptors such as the speech transmission index may be needed.[1]
For tall halls the design guide describes locating absorptive wall panels at high level, in addition to the roof liner, as effective but requiring significant coverage, and says the closer to the floor the treatment can be provided, the less coverage is required.[1] In its chapter on rooms for music it notes that occupants provide significant absorption in the lower half of a room, so absorption is often located at high level on the walls to give an even distribution.[1]
The numbers
- Sabine relation: T = 0.161 V ÷ A.[1]
- Sports hall reverberation limit, new build: 1.5 s under 280 m² floor area, 2.0 s above 530 m².[2]
- Foyer, entrance hall or atrium not used for teaching: 1.5 s or less new build, 2.0 s or less refurbishment.[2]
- Halls and recital rooms in schools are generally two storeys high, around 6 m, and group and practice rooms at least 3 m, according to the design guide.[1]
In schools and SEN settings
The National Deaf Children's Society says some subjects may be taught in an echoey hall, and recommends asking how listening conditions in that room could be improved.[3] The design guide says perhaps the most difficult areas for inclusion are large spaces such as assembly halls and sports halls.[1] BB93 sets tighter rows for rooms used specifically by pupils with special hearing or communication needs, including, for new build and refurbishment, a sports hall specified by an average from 125 Hz to 4 kHz.[2]
Worked example
These figures are illustrative, not a measured room. Take a dining space of 200 m² and a target reverberation time of 1.0 s.[1] At a ceiling height of 3 m the volume is 600 m³ and the absorption needed is 0.161 × 600 ÷ 1.0 = 96.6 m².[1] At 6 m the volume is 1,200 m³ and the absorption needed doubles to 193.2 m².[1]
What people get wrong
- Treating a tall room as a bigger classroom. Volume sets the absorption needed, so the same floor area needs twice the absorption at twice the height, for the same target time.[1]
- Counting on the formula alone. The design guide warns that the Sabine relation assumes an even sound field.[1]
- Placing all absorption high. The design guide says closer to the floor means less coverage is needed.[1]
How it is measured or checked
For sports halls and similar normally unfurnished spaces, BB93 accepts either a design to the Institute of Acoustics guide or measurement of the mid-frequency reverberation time following the Association of Noise Consultants testing guide.[2]
FAQ
Why does a high ceiling make a room echo?
A taller room has a larger volume, and reverberation time is proportional to volume at a given amount of absorption.[1]
Does lowering the ceiling help?
The design guide says reducing the ceiling height will generally reduce the reverberation time.[1]
Where should absorption go in a high room?
The design guide describes roof liners, absorptive wall panels at high level and hanging baffles for sports halls, with the nearer the floor the less coverage needed.[1]
WorkSpace Acoustics surveys and installs acoustic treatment; contact the team to discuss a room.
Sources
- Acoustics of Schools: a design guide. Institute of Acoustics and Association of Noise Consultants, November 2015. Accessed November 2026.
- Acoustic design of schools: performance standards (Building Bulletin 93). Department for Education, February 2015. Accessed November 2026.
- Creating good listening conditions. National Deaf Children's Society, last reviewed May 2025. Accessed November 2026.