What is reverberation time?

Reverberation time is how long sound takes to fade away in a room after the source stops, normally measured as the time for the sound level to fall by 60 dB.[1] It is quoted in seconds. Long reverberation times blur speech, so schools set maximum values for each type of room.[1]

Key points

  • Reverberation time is defined as the time for sound energy to fall to one millionth of its original intensity, a 60 dB reduction.[1]
  • It rises with the volume of the room and falls as the amount of sound absorption increases.[1]
  • BB93 sets a maximum for each school room type, for example 0.6 s for a new build primary classroom.[2]
  • A value is given per frequency band, and BB93 (new build and refurbishment alike) averages the 500 Hz, 1 kHz and 2 kHz bands into the mid-frequency reverberation time (Tmf).[2]

How it works

After a source stops, sound waves keep reflecting off the room surfaces and lose strength each time a surface absorbs some of the energy. The reverberation time describes how quickly that decay happens.[1]

For a room with an even, diffuse sound field, the time is proportional to the room volume and inversely proportional to the total absorption:[1]

T = 0.161 V / ΣSα seconds, where V is the volume in cubic metres and S and α are the area and absorption coefficient of each surface.[1]

The Institute of Acoustics says this relation should be used with caution. Many classrooms do not have a diffuse field because the absorption is not evenly spread, and in rooms with one dimension six times or more the others the reverberation time may not describe the room well.[1]

The numbers

BB93 gives maximum Tmf values for rooms that are finished, furnished and unoccupied.[2]

  • Primary classroom, class base or SEN calming room: 0.6 s new build, 0.8 s refurbishment.[2]
  • Secondary classroom or study room: 0.8 s new build, 1.0 s refurbishment.[2]
  • Open plan teaching area: 0.5 s for both.[2]
  • Sports hall: 1.5 s for floors under 280 m², rising to 2.0 s above 530 m², new build.[2]

Tmf is the average of the 500 Hz, 1 kHz and 2 kHz octave-band times, or of the one-third octave bands from 400 Hz to 2.5 kHz.[2]

In schools and SEN settings

A classroom with a reverberation time of several seconds makes syllables overlap and reduces speech intelligibility, and people raise their voices to compensate, a pattern the design guide links to school dining rooms and sports halls.[1] For rooms intended specifically for pupils with special hearing or communication needs, BB93 asks for 0.4 s averaged from 125 Hz to 4 kHz, with no band above 0.6 s, for new build.[2] The design guide lists the British Association of Teachers of the Deaf criterion as 0.4 s or less across 125 Hz to 4000 Hz.[1]

The National Deaf Children's Society lists reducing echoes and reverberation among the ways settings can improve listening conditions, including fabric on displays, carpeted areas and specialist acoustic boarding.[3]

Worked example

These figures are illustrative, not a measured room. A hard-surfaced room of 150 m³ with 15 m² of total absorption has T = 0.161 × 150 ÷ 15 = 1.6 s using the formula above.[1] To reach 0.6 s the room needs 0.161 × 150 ÷ 0.6 = 40 m² of absorption, so about 25 m² must be added.[1]

What people get wrong

  • One target for every room. The limits differ by room type, and by new build against refurbishment.[2]
  • Counting on furniture. Classroom furnishings are unlikely to provide significant absorption, although they can scatter sound onto absorbent surfaces.[1]
  • Trusting the formula blindly. It assumes a diffuse field and the guide warns about its limits.[1]

How it is measured

ISO 3382-2 specifies how to measure reverberation time in ordinary rooms: the procedure, the apparatus, the number of measurement positions, and how to evaluate the data and present a report.[4] For sports halls and similar unfurnished spaces BB93 accepts either design to the Institute of Acoustics guide or measurement following the Association of Noise Consultants testing guide.[2]

FAQ

What is a good reverberation time for a classroom?

BB93 sets a maximum Tmf of 0.6 s for new build primary classrooms and 0.8 s for secondary classrooms.[2]

Is reverberation the same as echo?

No. Reflections arriving within about 50 milliseconds of the direct sound blend with it, while strong later reflections harm speech and, if delayed enough, are heard as distinct echoes.[1]

Does a bigger room mean longer reverberation time?

For the same absorption, yes. The reverberation time is proportional to the room volume.[1]

WorkSpace Acoustics surveys and installs acoustic treatment; see how a survey works or get in touch.

Sources

  1. Acoustics of Schools: a design guide. Institute of Acoustics and Association of Noise Consultants, November 2015. Accessed November 2026.
  2. Acoustic design of schools: performance standards (Building Bulletin 93). Department for Education, February 2015. Accessed November 2026.
  3. Creating good listening conditions. National Deaf Children's Society, last reviewed May 2025. Accessed November 2026.
  4. ISO 3382-2:2008 Acoustics: Measurement of room acoustic parameters, Part 2: Reverberation time in ordinary rooms. International Organization for Standardization, June 2008, confirmed 2022. Accessed November 2026.
Expert acoustic consultancy and installation for schools, businesses and restaurants across the UK. Specialists in SEN environments.
A specialist division of: Presentation Spaces Group

COMPANY

About
Why Acoustics
Contact Us
Privacy Policy
Glossary
Acoustics statistics

SECTORS

Schools
Businesses
Restaurants

SERVICES

Acoustic Surveys
Acoustic Design
Installation
© 2026 WorkSpace Acoustics Ltd. All rights reserved.
Product images courtesy of Presentation Spaces Group (used with permission)