What is the weighted sound absorption coefficient (alpha-w)?

The weighted sound absorption coefficient, written alpha-w, is a single number from 0 to 1 that summarises how well a product absorbs sound across the octave bands from 250 Hz to 4 kHz.[1] ISO 11654 calculates it by shifting a reference curve towards measured values, and it underpins the absorption classes A to E.[1]

Key points

  • Alpha-w is defined in ISO 11654 as the value of a shifted reference curve at 500 Hz.[1]
  • It is built from the practical sound absorption coefficient, which is itself calculated from ISO 354 reverberation-room measurements.[1]
  • Shape indicators L, M and H flag a product that absorbs much more than the curve at low, middle or high frequencies.[1]
  • It is not suitable for every product or room; ISO 11654 says complete absorption data are needed for carefully designed spaces.[1]

How it works

An absorption coefficient is the share of sound energy a surface absorbs, from 0 for a totally reflective surface to 1 for one that absorbs everything that reaches it.[2] ISO 354 measures it in a reverberation room for each one-third-octave band.[3] ISO 11654 then averages each group of three one-third-octave values into an octave band, rounds the result in steps of 0.05, and caps it at 1.00 to give the practical sound absorption coefficient.[1]

The standard then fixes a reference curve and shifts it in steps of 0.05 towards the measured values until the unfavourable deviations, where the measurement falls below the curve, add up to no more than 0.10. The shifted curve's value at 500 Hz is alpha-w.[1]

The numbers

The unshifted reference curve has values of 0.80 at 250 Hz, 1.00 at 500 Hz, 1 kHz and 2 kHz, and 0.90 at 4 kHz.[1] Results are quoted to two decimal places, with shape indicators in brackets.[1] A shape indicator is added when a practical coefficient exceeds the shifted curve by 0.25 or more: L for 250 Hz, M for 500 Hz or 1 kHz, H for 2 kHz or 4 kHz.[1]

Worked example

ISO 11654 gives a worked case. An absorber has practical coefficients of 0.35 at 250 Hz, 0.70 at 500 Hz, 0.65 at 1 kHz, 0.60 at 2 kHz and 0.55 at 4 kHz.[1] Shifting the reference curve down by 0.40 gives 0.40, 0.60, 0.60, 0.60 and 0.50 across those bands. Only the 250 Hz band falls below the curve, by 0.05, which is within the 0.10 allowance, so alpha-w = 0.60.[1]

A shift of only 0.35 would give a curve value of 0.45 at 250 Hz and 0.65 at 2 kHz.[1] The deviations would then be 0.10 and 0.05, totalling 0.15, which is over the allowance, so the lower position is the one that applies.[1]

In schools and SEN settings

The Institute of Acoustics design guide asks for Class A absorbers over an area equivalent to 100% of the ceiling in open plan teaching spaces, where Class A is rated under ISO 11654.[2] A buyer comparing absorbers for a school room should ask for the alpha-w, any shape indicator, and the full coefficient curve, because the class and alpha-w do not show how a product performs at 125 Hz, which is below the rating curve.[1] The guide also says specialist advice from an educational audiologist and acoustician is needed for rooms for hearing impaired pupils.[2]

What people get wrong

  • Treating alpha-w as the performance of an installed system. It describes a tested sample, and ISO 11654 says the rating is often not suitable for single items such as chairs and baffles.[1]
  • Ignoring the shape indicator. An M or H after the number means the product absorbs far more than the curve in that range, so the number understates a narrow strength.[1]
  • Assuming low-frequency performance. The rating curve stops at the 250 Hz octave band, so it says nothing below that.[1]

How it is measured

Alpha-w is calculated, not measured directly. The input data come from an ISO 354 test in a reverberation room, where the specimen is a wall or ceiling treatment or an object such as a space absorber.[3] For products tested with an air space behind, the standard requires the depth of construction to be stated, and it notes that a depth of at least 200 mm is recommended in Europe.[1]

FAQ

What is a good alpha-w?

A higher value means more absorption on the standard's scale, up to 1. What is good depends on the room and the target set by the designer.[1]

Is alpha-w the same as the absorption class?

No. Alpha-w is the number; the class letter is derived from it using the classification in an informative annex of ISO 11654.[1]

Does alpha-w depend on how the product is mounted?

Yes. The test mounting matters, so the depth of construction must be reported for products tested with an air space.[1]

WorkSpace Acoustics surveys and installs acoustic treatment; contact the team to discuss a specification.

Sources

  1. ISO 11654:1997 Acoustics: Sound absorbers for use in buildings, Rating of sound absorption. International Organization for Standardization, April 1997, confirmed 2023. Accessed November 2026.
  2. Acoustics of Schools: a design guide. Institute of Acoustics and Association of Noise Consultants, November 2015. Accessed November 2026.
  3. ISO 354:2003 Acoustics: Measurement of sound absorption in a reverberation room. International Organization for Standardization, May 2003, confirmed 2024. Accessed November 2026.
Expert acoustic consultancy and installation for schools, businesses and restaurants across the UK. Specialists in SEN environments.
A specialist division of: Presentation Spaces Group

COMPANY

About
Why Acoustics
Contact Us
Privacy Policy
Glossary
Acoustics statistics

SECTORS

Schools
Businesses
Restaurants

SERVICES

Acoustic Surveys
Acoustic Design
Installation
© 2026 WorkSpace Acoustics Ltd. All rights reserved.
Product images courtesy of Presentation Spaces Group (used with permission)